 งานวิจัยผลกระทบของการระบายน้ำของระบบหล่อเย็นจากโรงไฟฟ้าบางปะกงที่มีต่อสิ่งแวดล้อมของสัตว์น้ำในแม่น้ำบางปะกง (1999)หัวหน้าโครงการ: ดร.กังวาลย์ จันทรโชติ, รองศาสตราจารย์ ผู้ร่วมโครงการ: นายธีระ เล็กชลยุทธ, ผู้ช่วยศาสตราจารย์ , นางกาญจนา พัฒธนานุรักษ์, ผู้ช่วยศาสตราจารย์ , ดร.มณฑล อนงค์พรยศกุล, ผู้ช่วยศาสตราจารย์ , นายพงศ์เชฏฐ์ พิชิตกุล, ผู้ช่วยศาสตราจารย์ , ดร.สุริยัน ธัญกิจจานุกิจ, ผู้ช่วยศาสตราจารย์ , ดร.ภูวดล โดยดี, ผู้ช่วยศาสตราจารย์ , นางสาวศันสนีย์ หวังวรลักษณ์, ผู้ช่วยศาสตราจารย์ แหล่งทุน:การไฟฟ้าฝ่ายผลิตแห่งประเทศไทย |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 หัวเรื่อง:ไม่มีชื่อไทย (ชื่ออังกฤษ : Simulation of Heat and Mass Transfer in the Corrugated Packing of the Counter Flow Cooling Tower) ผู้เขียน: ดร.มนตรี พิรุณเกษตร, รองศาสตราจารย์ , ดร.สันติ ลักษิตานนท์, รองศาสตราจารย์ สื่อสิ่งพิมพ์:pdf AbstractThis paper presents the simulation results of the heat and mass transfer characteristics of corrugated packing in a counter-flow cooling tower. The numerical analysis has been partially validated by comparing the experimental data from a testing apparatus of a cooling tower under the same conditions at inlet dry bulb temperature of 32.3?C, inlet wet bulb temperature of 25.2?C and inlet water temperature of 40?C. Due to the complicated configuration of the packing surface and its installation, it was not possible to measure the temperature of the air and water in the intermediate section, but only the exit air temperature and exit water temperature. It was found that the errors between the calculated and measured temperature of the exit air were less than 2.5% for the exit dry bulb temperature, less than 2.2% for the exit wet bulb temperature and for the exit water were less than 1.3% (by testing at L/G=1.800, 2.171 and 2.820). A comparison of the volumetric heat transfer coefficients derived from the experiment and the simulation using the Tchebycheff method found that all the errors were less than 4.8%. Consequently simulation can be used as a tool for studying the phenomenon of heat and mass transfer in corrugated packing. |
 หัวเรื่อง:ไม่มีชื่อไทย (ชื่ออังกฤษ : Study on the Effect of Blade Angle on the Performance of a Small Cooling Tower) ผู้เขียน: ดร.มนตรี พิรุณเกษตร, รองศาสตราจารย์ , ดร.สันติ ลักษิตานนท์, รองศาสตราจารย์ สื่อสิ่งพิมพ์:pdf AbstractThis paper presents the effect of blade angles on the packing characteristic curves of a small cooling tower on the site experimental data. The volumetric heat transfer coefficient (KaV/L) can be illustrated graphically and varied with the water to air flow ratio (L/G) for the blade angles of 59?, 67 ?, 75?, and 83?, respectively. The curves can be constructed by the experimental data from the cooling tower testing in accordance with the procedure of CTI standard. It was found that the characteristic curves can be represented in the form of KaV/L = C(L/G)-n in the different range of L/G for each blade angle. Finally, it was found that the cooling tower can operate under all the given approaches (5?C, 6?C, 7?C and 8?C) at the blade angle of 67? by maintaining the cooling range of 5?C, wet bulb temperature of 26?C, and water flow rate of 3.9 m3/h. |
 หัวเรื่อง:ไม่มีชื่อไทย (ชื่ออังกฤษ : Simulation of a Counter-Flow and Cross-Flow Cooling Tower by the Stepwise Integration Method) ผู้เขียน: ดร.มนตรี พิรุณเกษตร, รองศาสตราจารย์ สื่อสิ่งพิมพ์:pdf AbstractThe stepwise integration method is an approximation method for determining the water temperature in the fill layers for a counter-flow cooling tower and in the fill cells for a cross-flow cooling tower. Accordingly, it can be assumed that the mean driving force in each layer is a constant and the water temperature difference of each layer is equal to the cooling range divided by the required number of layers. Thus, the stepwise integration method can predict the volumetric heat transfer coefficient, the outlet temperatures of the water and air passing through the cooling tower and also determine the operating points of a cooling tower with a known value of KaV under a given approach. However, the stepwise integration method can also simulate and plot the approach curve by condition 1 ( given the inlet and outlet temperatures of water), and the characteristic curve by condition 2 ( given a value of KaV for the entire fill). In a cross-flow cooling tower, where the value of KaV for the entire fill, the flow rates of the entering air and water, the inlet dry bulb and inlet wet bulb temperatures and the hot water temperature are known, it is possible to predict the outlet water temperature by the stepwise integration method. In addition, the stepwise integration method can be used to simulate and plot the approach curve using condition 1 and the characteristic curve using condition 2. |
 |
 |
 |
 |
 |
 |